info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Video, LED and playback

MD-HX and MD-LX: choose conversion or scaling for an event

Compare MD-LX direct conversion with the MD-HX scaler. These setup notes apply to MD-HX serial prefixes CLA/CLB/CLC and manual 1.5; identify the serial prefix before rehearsal.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Connect the content to its event destination

For a conference, stand or presentation in Argentina, a laptop, camera and display may need different formats. Tell us what you want to show and what production supplies. Ask us to quote video preparation, distribution, playback and operation, coordinating conversion and tests with each signal owner.

MD-HX and MD-LX: choose conversion or scaling for an event

If you need HDMI and SDI connections without changing format, begin with a compatible direct path. If resolution or frame rate must also change, review a device with a scaler. Choose around complete framing, readable text, motion and audio at the final destination.

Model, serial prefix and documentation

MD-LX documents direct HDMI/SDI paths and conversion between 3G Level A and B. Its V1.0 brochure does not document resolution or frame-rate scaling. For MD-HX, the manufacturer directs CLA/CLB/CLC to manual 1.5 and CLD/CLE/CLF to separate documentation. These controls apply only to CLA/CLB/CLC with manual 1.5; record installed firmware and visible controls without updating the unit to identify it.

Check input, scaler and output separately

On MD-HX 1.5, Input Status distinguishes S, H and D. D describes scaler output; the physical connector may still take a direct input. For HDMI-to-SDI conversion, check DUC Source, Output Format and SDI OUT SOURCE, then verify the format received at the destination. Check HDMI OUT SOURCE separately and Output 1 is loop when using that SDI pair.

Reference and laptop changes

DUC REF offers SOURCE, FREE-RUN, SDI IN and HDMI IN. FREE-RUN means operation without a reference; it does not verify content or synchronization with another system. Define the required reference and compare laptop A, disconnection and laptop B off-air, recording received format and picture/audio recovery.

Test framing with actual content

Compare direct HDMI and the full chain using the same border-and-circle pattern. Record received signal, picture width, bars, cropping and distortion. A 16:10 projector does not establish a 1920 × 1200 converter output. If formats match, check that projector input’s settings in its manual before changing aspect or resetting.

Audio pairs, return and actual content

MD-HX 1.5 Audio separates HDMI Out Pair 1–4 and SDI Out Pair 1–8; each selector takes a source pair or Off. Save all values before preparing HDMI without audio, then check SDI program and any active loop. HDMI OUT TYPE separates DVI from two- or eight-channel HDMI modes. Pair selection does not swap its channels or document 5.1 downmix. Prepare and test the remote mix-minus on its own path.

Change one condition and preserve recovery

Record model, serial prefix, firmware, input state, reference and output sources. Parameter changes affect the signal while scrolling, so compare off-air with controlled monitoring. Restore actual content, then check edges, motion and sound at each receiver. The manual says to wait until the save S disappears before powering down after changes.

Decisions before rehearsal

Does MD-LX change resolution or frame rate like MD-HX?

Its V1.0 brochure documents direct paths and formats, not that scaling or frame-rate conversion block. Choose by the required function and verify input and output as well as connectors.

Which manual applies to an MD-HX with a CLA serial prefix?

The official page directs CLA/CLB/CLC to 1.5. For CLD/CLE/CLF, consult their own documentation and actual controls; this guide does not transfer functions across revisions.

Does the correct D format prove the SDI output?

D represents the scaler. Check SDI OUT SOURCE, actual BNC, Output 1 is loop and the format received at the destination.

Does FREE-RUN guarantee uninterrupted capture during laptop changes?

Manual 1.5 defines it as operation without a reference. Test actual receiver and content, recording interruption and recovery; the setting does not establish switching without black frames.

Can I mute all HDMI by switching only the first pair Off?

Identify and check all four HDMI Out Pair values; the first pair Off does not verify the others. Preserve SDI selections and listen at every destination, including any loop.

Does HDMI OUT TYPE 2C create a stereo mix from 5.1?

The manual distinguishes output types and channel counts without documenting a downmix there. Identify the contents of each pair and prepare the required mix on equipment that documents that function.

Information for quoting preparation, connections and operation

You can enquire without knowing the converter. Describe the content, where it must appear and what each team supplies. Add city, date or running order when known. Agree on equipment, cabling, setup, rehearsal and who operates changes. The worksheet is optional; downloading it does not send an enquiry.

Download conversion, source-change and audio worksheet (TXT)

Can I enquire before knowing formats or models?

Yes. Tell us the goal and the part you want to hire. Start with sources and destinations, then complete models, formats and schedules with production. If a system already exists, preserve its settings to prepare testing.

Continue with the signal destination

External manufacturer documentation

Open the MD-HX 1.5 manual for CLA/CLB/CLC or the MD-LX V1.0 brochure on the official site. Documents are in English. For other serial prefixes, select the relevant documentation on the manufacturer page.

Documentation consulted

Documentation cross-checked: October 30, 2026. Identify model, serial prefix and installed firmware before applying settings.

Let’s prepare your event system

Tell us what you want to show, hear or light and what your production already provides. Start with the idea and add models, dimensions and schedules later. Mention the model or guide in your message; the related service is selected in Contact.

Enquire about equipment and servicesView the related serviceEvent preparation guide