info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Video, LED and playback

AJA GEN10: rack reference and checks with FS4

Trace content and reference separately. Identify groups, formats and receivers before preparing system synchronization.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Equipment, integration and event preparation

Tell us which signal must arrive and what your production supplies. Ask Eventos Globales about video equipment rental, purchase and integration, preparation and operation in Argentina. Start with an idea and diagram; the proposal identifies equipment, cable routes, access, tasks and responsibilities.

Prepare a shared rack reference

For cameras, switching, recording and screens, identify equipment requiring external reference and equipment supporting input synchronization. Assess reference generation/distribution or source processing. Separate equipment, configuration, measurements, rehearsal and event operation in the proposal.

GEN10 and FS4 do different jobs

Generating a shared reference and synchronizing video sources are different tasks. GEN10 and a frame synchronizer serve different purposes.

The GEN10 Mini-Converter manual v1.0r2, dated July 3, 2014, pp. 4–5, describes a generator with six video-reference outputs in two groups and one AES-11 output, all from a common timebase. Its connection diagram shows no input for processing a camera's or computer's content. Generating reference does not add frame-synchronizer processing.

The FS4 v3.1r1 · Ref Loop, says Ref Loop accepts SD blackburst or HD tri-level sync. Its two BNC connectors form a passive loop: one receives reference and the other continues the chain or is terminated. The second BNC does not generate a new reference. For source processing, see the FS4 format, audio and synchronization guide.

Start with the symptom: missing reference at a device, an unsynchronized video source, or an incompatible format. Record whether the source has a reference input and which formats it accepts. Carbonite resources and licenses depend on the exact model and manual; no one frame-synchronizer count applies across the whole family.

Identify the output group, signal and rate before changing DIP settings

Technical reference retained from the kit: compare the complete DIP matrix with the named manual edition and the actual unit label before applying settings.

In GEN10 v1.0r2, pp. 5 and 8, SW1 selects SD or HD for OUT 1–4, and SW2 does the same for OUT 5–6. Left selects SD; right selects HD. AES-11 is a separate output. Do not mistake it for one of the six video-reference BNC connectors.

SW4–SW8 select the HD family and format according to the matrix on p. 9. Record the BNC and group in use before comparing signals. If both groups output HD, do not assume that each connector has an independent HD format; the format controls are shared. Selecting SD or HD for a group does not, by itself, establish the exact rate.

The following table shows four combinations documented on p. 9. For a group to output the HD signal in a row, its SW1 or SW2 must be set to HD. Read the column heading carefully: the matrix lists SW8, SW7, SW6, not SW6, SW7, SW8. Zero means left and one means right, following the orientation printed on the device.

The installation instructions, p. 6, say to disconnect +5 VDC before setting DIP switches and connecting devices, then apply power last. Schedule this change outside the show because the generator may feed several devices. Photograph or record the initial settings, configure the agreed format and verify what each branch receives before returning to the event.

SW3, p. 8, selects Color Black or bars on the SD outputs and, at the same time, silence or tone on AES-11. Check that effect if the rack uses the audio output. The internal jumper, p. 7, relates to the NTSC pedestal; the manual does not require changing it to generate HD or NTSC with Setup. Do not treat it as a 59.94-versus-60 selector.

Identify the output group, signal and rate before changing DIP settings
HD reference for this rowSW4 (FORMAT)SW5 (HD FMT)SW8 / SW7 / SW6
1080i59.94Left.Left: 1080.0 / 0 / 0.
720p59.94Left.Right: 720.0 / 0 / 0.
1080i60Left.Left: 1080.1 / 0 / 0.
720p60Left.Right: 720.1 / 0 / 0.

For a 1080p59.94 system, check the reference accepted by each receiver

Check the reference accepted by each receiver in the setup and measure latency before and after changes.

The list in GEN10 v1.0r2, p. 10, includes 1080i50/59.94/60, 720p at the listed rates and 1080p through 30; it does not list 1080p59.94 or 2160p reference. That list describes what GEN10 generates. Show content format and reference format are separate facts. Check the exact receiver manual for compatibility; a shared “1080” label is not enough.

For FS4, FS4 v3.1r1 · About Reference and Genlock Source, requires a reference compatible with the output frame-rate family: 59.94/29.97/23.98, 50/25 or 60/30/24. FS4 v3.1r1 · VIDEO · Output Frame Rate / Genlock Source, select the family and source; changing the family recalls a stored Output Format. Record the final format after making that change.

List each receiver model, version, connector, accepted references and received signal. Check the rate combination in the exact camera, switcher or capture-card manual; documented FS4 compatibility does not verify other equipment.

There is a picture, but FS4 shows No Ref, No Input or Incompat for GEN

The FS4 v3.1r1 · Incompatibility Alarms, shows a valid video input with missing reference, and another example with incompatible reference. In FS4 v3.1r1 · STATUS, IN, GEN and OUT are read for each processor. Record the alarm and format on each path: seeing content does not validate reference.

If FS4 v3.1r1 · VIDEO · Output Frame Rate / Genlock Source is set to Reference and GEN detects no signal, trace the path from the GEN10 BNC to Ref Loop. Check the SD/HD group, DIP settings, power and cable. FS4 v3.1r1 · Ref Loop requires a stable reference and 75-ohm termination at the FS4's unused BNC or at the last device in the chain. Identify where the branch is terminated; do not add another terminator without checking the next device's configuration.

If GEN shows Incompat, record the detected format and compare it with the selected frame-rate family and Output Format. If there is no signal, the format table cannot replace a check of the physical path. For a controlled test, compare a known-good cable and reference output while keeping the agreed format; record the result before changing another variable.

Free run uses the FS4's own timebase. If you compare it outside the show, record the change and what the switcher receives. An alarm disappearing does not prove lock to the shared generator. Restore the required mode afterward and check switching and every destination.

Complete the blank GEN10/FS4 reference worksheet. Record reference, picture and audio states separately, with the date and result of each test.

There is a picture, but FS4 shows No Ref, No Input or Incompat for GEN
Observed stateWhat to checkRecord for follow-up
IN has video; GEN detects no referenceGenlock Source, GEN10 output/group, cable and termination.IN/GEN/OUT states and the point where the signal was checked.
GEN detects a signal but reports IncompatReceived format, frame-rate family and Output Format.Complete values, including the 59.94/60 distinction.
Ref Loop continues to another deviceLast receiver and its termination according to its manual.Branch diagram and location of the 75-ohm termination.
Temporary comparison in Free runSwitcher acceptance and the mode required by the setup.Proposed or executed result and settings needed to return.

Frequently asked questions

Does GEN10 add frame synchronizers to a Ross Carbonite?

GEN10 generates reference; it does not process video sources or add input frame synchronizers. Record the exact model, sources and symptom before checking resources or licenses; a single count does not apply to the whole family.

Does the FS4's second Ref Loop BNC generate reference for the switcher?

The two BNC connectors form a passive loop. One receives external reference; the other continues the chain or is terminated. It is not an independent generator output. Trace where the signal comes from and where it ends. For FS4, p. 24 requires a stable signal and 75-ohm termination.

Why does one GEN10 BNC output SD while another outputs HD?

OUT 1–4 and OUT 5–6 are separate groups. SW1 selects SD/HD for the first and SW2 for the second; left is SD, right is HD. Record the BNC in use before checking SW4–SW8. AES-11 is a separate connection and does not provide those groups' video reference.

Does setting SW4 to 59.94 guarantee that GEN10 is not generating 60?

Check the full matrix combination, not only SW4. With SW4 left, SW8/SW7/SW6 at 0/0/0 select the 1080i59.94 or 720p59.94 rows depending on SW5; 1/0/0 selects 1080i60 or 720p60. The group must be set to HD. Verify the received signal before treating 59.94 and 60 as equivalent.

Does GEN10 generate 1080p59.94 or 2160p reference because the show uses that format?

Those formats are absent from the GEN10 v1.0r2 list. Record content format and the references accepted by each receiver separately. Devices may have different requirements. A reference documented as compatible with FS4 does not establish compatibility with Canon, ATEM or DeckLink.

How should we check the reference accepted by each camera?

Record model and firmware, available input, reference type and supported rates. Check the actual combination and lock indicator in that camera’s documentation and rehearse it with the system before the event.

What should I check when FS4 has an SDI picture but GEN shows No Input?

If Genlock Source is set to Reference, check the signal at Ref Loop from the generator's group and BNC, with the cable and termination identified. IN and GEN describe separate paths. Record OUT as well. If GEN detects a format but shows Incompat, compare it with the selected frame-rate family and output.

Does GEN10 SW3 change only the SD reference bars?

According to p. 8, it also changes AES-11: left outputs silence and SD Color Black; right outputs tone and SD bars. Check audio branches that use this output before changing it. Record the original DIP settings and schedule the change outside the show, following the installation instruction to disconnect +5 VDC.

Check every receiver before switching

List each device version, accepted reference, BNC and group, received status and output format. Separate absent signal, incompatibility and unsynchronized video. Agree a test window, record initial settings and verify return to the intended mode before the audience arrives.

Rental, purchase and integration: starting information

Can we enquire while the rack is still being designed?

Yes. Share city, date, planned sources and destinations and each supplier’s contribution. Compare equipment and preparation, then complete references and versions before rehearsal.

Can the proposal include preparation and operation?

Assess the required scope: supply, distribution, configuration, receiver verification and operation. Identify who authorizes changes and who preserves and restores system settings.

Start with the route and required result

Share city, date, signal sources and destinations, estimated distances and available equipment or infrastructure. State equipment, integration, installation, preparation or operation needs. Missing details can remain to be defined. Contact arrives with Video and cameras selected; include the guide name in your message and review the draft before sending.

Worksheet for production and venue coordination

Download editable transport and reference worksheet (TXT)

Continue with conversion, switching or the other path

Sources and model documentation

This documentation applies to GEN10, not OG-GEN10. GEN10 v1.0r2 is dated July 3, 2014 on its cover and July 8, 2014 in support. FS4 v3.1r1 is dated September 3, 2026. Locate sections by name and check the unit version.

Documentation consulted

Checked October 30, 2026: official specifications and support pages. The technical baseline comes from the kit; full manual review and checks of actual unit settings remain pending.

Let’s prepare your event system

Tell us what you want to show, hear or light and what your production already provides. Start with the idea and add models, dimensions and schedules later. Mention the model or guide in your message; the related service is selected in Contact.

Enquire about equipment and servicesView the related serviceEvent preparation guide