info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Sound

Shure ANX4: distinguish displayed channels, licenses and audio to the console

Before counting available microphones, separate selected wireless family, enabled channels and audio path. Names on screen or an audible test do not establish that every voice reaches the event’s intended destinations.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Model and documentation reference

Exact reference: Shure ANX4 receiver. AD4D or AD4Q configurations do not transfer merely because they share a brand. The consulted English guide is document version 3.1 (2026-J), not confirmation of installed firmware. Axient Digital and ULX-D are alternative operating modes; ANX4 does not run both families simultaneously. Identify each transmitter and antenna’s full model, band and version without inferring local RF authorization.

Shure · ANX4 · Exact model and alternative modes · Shure ANX4 · English guide 3.1 (2026-J) · pp.4–6,36–38,42

Event application

For a panel, conference or performance in Argentina, create one row per voice with transmitter, use and destination. Separate simultaneous channels from spares or changes between program blocks. Request the active-channel state of the proposed unit rather than its advertised maximum. Add console, recording, remote feeds and RF coordination owner; the proposal must identify equipment, existing licenses, accessories and operation without assuming availability.

Documented maximum capacity: alternative modes

Documented maximum capacity: alternative modes
ModeDocumented maximumVerify
Axient Digital16Enabled channels and compatible transmitters
ULX-D24Enabled channels and compatible transmitters

Shure ANX4 · English guide 3.1 (2026-J) · pp.4–6,36–38,42

Displayed channels are not the same as licensed channels

The manual distinguishes available capacity, licensed count and displayed count in Channel Count. More channels may be displayed for preparation, naming and coordination; that does not enable their outputs. Record License Status and applicable limits with the administrator without changing accounts, activations or codes. The guide says changing displayed count may restart the receiver, so it is not an innocent on-program status check. An unlicensed wireless channel is not enabled by renaming it or changing the patch.

Shure ANX4 · English guide 3.1 (2026-J) · pp.4–6,36–38,42

Listening, test tone and microphone delivery are separate tests

Documentation distinguishes Dante/AES67 digital output, headphone monitoring and receiver control. Dante Browse may monitor another network source; identify what you are hearing before concluding the microphone is received. A test tone helps check a path but does not establish RF reception or enable every voice. Separately check RF signal, channel audio, On/Mute output state, network subscription and console input. Do not infer analog XLR outputs from a generic polarity row in a sheet; verify actual connectors. Dante audio reaching a console also does not establish remote control from every console.

Shure ANX4 · English guide 3.1 (2026-J) · pp.4–6,36–38,42

Prepare checks per voice and destination

  1. Record receiver, firmware, active mode, displayed/licensed counts and administrator-reported restrictions. Preserve the state without activating or transferring licenses.
  2. Inventory transmitters by full model, band and version. Compare selected family and coordinated RF plan; do not mix families because frequencies coincide.
  3. Map each voice through receiver, digital output channel, subscription, console input and final mix. Distinguish that path from monitoring and control.
  4. Agree on test level and destination owner. Record whether listening used the actual microphone, another Dante source or tone, and which meter was observed.
  5. During actual rehearsal check each voice at audience, foldback, remote or recording destinations. Keep unverified channels and integrations pending rather than declaring availability from a display or tone.

Shure ANX4 · English guide 3.1 (2026-J) · pp.4–6,36–38,42

Frequently asked questions

Can one ANX4 add 16 Axient Digital and 24 ULX-D channels?

No. These are maxima for alternative modes, not additive counts or simultaneous families.

Does displaying 12 channels establish 12 enabled outputs?

No. Displayed and licensed counts are separate. Record the unit’s actual state.

Does hearing headphones confirm microphone output to the console?

No. Identify the listening source, then separately check output, subscription and console input.

Does a tone at the console establish every microphone works?

No. It tests part of a path; each voice still needs RF reception, entitlement and audio verification.

Must licenses or firmware be changed before an inquiry?

No. Share existing states and versions. A technical inquiry activates no channels, administers no accounts and confirms no compatibility or availability.

Follow control and distribution

Download the voice, license and destination worksheet (TXT)

Official edition-specific documentation

ANX4 English guide 3.1 (2026-J): modes/licenses pp.4–6; audio/tone p.36; headphones/Dante Browse p.37; displayed count p.38; status/limits p.42. The 2025 product sheet is platform reference, not proof of analog connectors, licenses or unit firmware. ES/PT guides are our own explanations based on the cited English edition.

Plan sound for your event

Include date, city, venue, simultaneous voices and destinations. If ANX4 is already involved, add mode, firmware, enabled-channel count, existing transmitters and console without passwords or access information to prepare an EG sound inquiry.

Enquire about equipment and servicesView the related serviceEvent preparation guide