Model and documentation reference
The reference is Yamaha QL1. Its 16 local INPUT sockets and 8 OMNI OUT sockets are not its mixing-channel count and must not be confused with QL5. Owner’s Manual B0 and Reference Manual V5.8 E0, 10/2022, explicitly cover QL1. An edition does not establish installed firmware or support for a particular rack: identify console, device, versions and actual cards.
Yamaha · QL1 · Exact model overview · QL5/QL1 · Owner’s Manual B0 · EN · pp.16–17,32
Event application
For a conference in Argentina, create one row per voice and playback source, with audience, stage, remote and recording destinations. If the venue provides console or rack, request port names and a current patch photo. Separate existing equipment from proposals; do not load another event’s scene just to prepare an inquiry. A sketch and program support planning a test even before the equipment list is complete.
Three separate patches for a Dante source
| Screen | Connection | Record |
|---|---|---|
| DANTE INPUT PATCH | Transmitter to QL1 Dante receiver (1–32) | Device, transmit and receive channels |
| GAIN/PATCH | Input port to mixing channel | Selected source and channel |
| OUTPUT PORT | Output channel/bus to physical or Dante port | Mix, port and actual destination |
QL5/QL1 · Reference Manual V5.8 E0 · EN · 10/2022 · pp.17–19,163–166,249–254
Trace the source before changing a patch
V5.8 distinguishes DANTE INPUT PATCH from a channel’s input selection. QL1’s built-in receiver covers DANTE1–32; DANTE33–64 is listed for QL5 only. Check transmitter and receiver, then the source chosen in GAIN/PATCH or PATCH/NAME. If the channel receives signal, trace processing, ON, fader and assignment to the intended mix. Check OUTPUT PORT and actual destination separately; hearing CUE does not itself establish room output. Do not assume INPUT numbering guarantees assignment to the same-numbered CH.
QL5/QL1 · Reference Manual V5.8 E0 · EN · 10/2022 · pp.17–19,163–166,249–254
Network link and remote control are different evidence
PRIMARY/SECONDARY are Dante connectors; NETWORK is the separate control connector described in B0. Record cabling, clock, messages and device status without changing topology as an on-program diagnostic. The reference distinguishes head-amp control from audio transport. If a patch cannot be edited, record DANTE PATCH BY, CONSOLE ID and the message before coordinating intervention; do not change ownership or permissions as a shortcut. AUTO SETUP can repatch according to registered devices: preserve the setup and do not treat it as a read-only status check.
QL5/QL1 · Reference Manual V5.8 E0 · EN · 10/2022 · pp.17–19,163–166,249–254
Prepare a recoverable source-by-source test
- Preserve show, scene and current patch photos; record exact firmware and models. Keep the backup distinct from a proposed new scene.
- Document transmitter, Dante receiver 1–32, channel input port and intended mix. Add output and listening or recording destination.
- Agree on level and destination cut control with the system owner. Compare a known source and one observation point at a time.
- If signal is missing, record the patch stage where it disappears. Separate subscription from internal patching rather than changing gain, clock and assignments together.
- After an agreed correction, verify speech and playback at each actual destination. Restore rejected changes and leave backup, preserved setup and unresolved items.
QL5/QL1 · Reference Manual V5.8 E0 · EN · 10/2022 · pp.17–19,163–166,249–254
Frequently asked questions
Does seeing the rack establish its microphone is on CH1?
No. Check Dante reception and then the channel source. Device identification does not replace those two patches.
Does NETWORK carry the rack’s Dante audio?
The manual distinguishes NETWORK for control from PRIMARY/SECONDARY for Dante. Identify the actual port before tracing the remaining path.
Are DANTE INPUT PATCH and GAIN/PATCH the same?
No. The former selects the received network source; the latter assigns a port to the mixing channel. Record both.
Is AUTO SETUP merely a status display?
No. It can apply automatic patching. Do not execute it as an innocent observation of the current show.
Does V5.8 documentation confirm support for every newer rack?
No. Actual console, firmware, device and control scope need specific references. This guide also confirms neither availability nor a physical test.
Follow control and distribution
Official edition-specific documentation
B0: connectors pp.16–17 and output/listening p.32. V5.8 E0: input/output pp.17–19; DANTE INPUT PATCH pp.163–165; HA control p.166; Dante settings pp.249–254. Printed numbers. The linked PDFs are existing editions; check complete documentation and actual system compatibility before operation.
- Yamaha · QL1 · Exact model overview
- QL5/QL1 · Owner’s Manual B0 · EN · pp.16–17,32
- QL5/QL1 · Reference Manual V5.8 E0 · EN · 10/2022 · pp.17–19,163–166,249–254
- Yamaha · QL series · Official documentation index
