info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Sound

Shure ULXD4Q: four voices, room and recording

Prepare four receiver channels with identified transmitters and decide which voices must arrive separately or mixed.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Prepare voices for your event

Tell us the city, date, speakers and their movements. Eventos Globales can prepare a sound equipment rental, purchase and integration proposal, preparation and operation in Argentina. Start with the program and your team’s resources; complete models and connections during preparation.

Keep each voice through to the agreed feed

For conferences or panels, define simultaneous speakers and room, camera, recording or remote needs. Assess equipment, RF preparation, patching, console integration and operation. The proposal identifies each party’s resources and who verifies every feed.

Model and application

Receiver channels
4
Analog audio
XLR mic / line
Network audio
Dante
Synchronization
IR
Output options
Direct / Audio Summing

This is the quad ULXD4Q. Record its regional band and firmware; do not apply ULXD4D channel counts or assume every ULX-D band combination works.

Connections and required equipment

Transmitter → receiver RF/audio → direct or summed XLR/Dante → console. Wireless Workbench control is separate from a successful audio subscription.

Room and recording outputs: decide before summing

For a conference, decide whether you need each voice separately or an already combined mix. A track per speaker supports later balance decisions; a finished mix serves a different brief. Agree the deliverable before choosing cabling.

Audio Summing changes both XLR and Dante outputs. Switching connections cannot separate voices already summed in the receiver. To retain individual sources, verify Audio Summing OFF and each channel’s mapping before rehearsal.

If the room needs a mix but recording needs separate voices, keep channels separate into a console or recording system with enough routing, and build the agreed destinations there. Decide whether recording follows faders and mutes; room balance changes should not affect it accidentally. The actual options depend on the chosen system.

XLR connects to suitable analog inputs: match mic/line level and gain. Dante needs destinations able to receive that audio and a network configured for the selected mode. Wireless Workbench control does not replace the audio path. Choose by the actual equipment and inputs, not the connector alone.

At rehearsal, test one voice at a time and check its room and recording destinations. If tracks intended to be separate receive the same mix, compare Audio Summing and patch first; do not sum duplicate feeds again. Record the final map without changing a system in use.

Prepare the system

  1. Save receiver configuration and document transmitter models/bands.
  2. Coordinate legal frequencies and match the supported tuning range.
  3. Protect destinations before testing one channel.

Questions and troubleshooting

A transmitter fails to sync or RF appears without usable audio.

An RF indication alone does not confirm a valid audio link.

  1. Use the exact mixed-band compatibility tables when applicable; perform IR sync to the selected receiver channel and confirm success. Check encryption/sync warnings and transmitter mute.
  2. Compare receiver audio with the intended output. If incompatible or still silent, record bands, versions and messages for support rather than disabling security.
Two console inputs unexpectedly carry the same mix.

Inspect receiver Audio Summing before repatching the console.

  1. Read DEVICE UTILITIES > AUDIO SUMMING. Its selected groups affect XLR and Dante; Frequency Diversity is a different function.
  2. If isolated channels are intended, plan a protected change to OFF and verify each channel separately. Preserve an intentional summed design; do not sum again downstream blindly.
Receiver audio meters, but Dante or console control fails.

Audio transport and remote control need separate evidence.

  1. Match SWITCHED, REDUNDANT AUDIO or SPLIT to the official port map. Check subscription and clock for audio; application/interface and Yamaha Device ID for compatible console control.
  2. Do not change mode during a show. The manual requires removing network connections and a restart when changing it. If unresolved, preserve event logs, topology and versions for support.

Choose the next check

Choose the next check
ObservationNext checkWhat to record
No usable wireless audioBand/IR/muteSync result and audio meter
Duplicated mixAudio SummingGroup and destination
Network failureMode/clock/controlLogs and exact versions

Precautions

  • Keep redundant networks separate.
  • Match XLR mic/line level to the console input.
  • No generic factory reset, firmware update or copied IP plan.

Prepare four voices and an identified RF system

For four panel voices, list every transmitter, regional band, capsule/microphone and receiver channel. ULXD4Q provides four receiving channels; it does not mean four transmitters, batteries and antennas are included. Validate the band for the venue and each unit.

Map antenna A/B paths, coax, distribution and power. The guide permits RF cascade to one additional receiver in the same band; do not extrapolate an unlimited chain or choose coax by BNC shape alone. Identify active/passive antennas and their documented power requirements.

Compare wired microphones for a fixed panel, a prepared wireless system or a mixed setup. Start with date, venue, simultaneous voices and approximate movement. Scope equipment, RF coordination, antennas, room/remote patch and operation separately. Rehearse actual positions: four catalog channels do not prove venue coverage.

More setup questions

Does a ULXD4Q receiver alone provide four microphones?

It requires compatible transmitters, microphones/accessories, power, antennas and output paths. Confirm the whole system for the band and venue before finalizing the proposal.

Choose individual channels or Audio Summing

ULX-D Dual/Quad manual v8.3 (2025-J) describes Audio Summing for XLR and Dante. For independent tracks, keep channels separate and build later mixes where appropriate. Record network mode and port map; schedule mode changes out of use, disconnecting the network and cycling power as the manual requires.

Choose equipment, preparation and operation

When should voices stay separate?

When each participant needs later adjustment or separate mixes for room, remote and recording. Describe the deliverable; define sources, console, routing and destination checks before choosing the configuration.

How do we start when the venue already has microphones and a network?

Share known models and bands, the network owner and the missing feed. Assess integration, additional equipment, preparation and operation. Check compatibility against the identified system; a receiver photograph does not define the whole setup.

Tell us who speaks and what each destination needs

City, date, simultaneous voices and movement allow a proposal to start. Choose equipment, preparation, integration or operation for your needs. Contact arrives with Sound selected; mention EW-D 835-S or ULXD4Q in the message if relevant. Complete models later and review before sending.

Record the test of each voice

Reuse the optional speech rehearsal worksheet: speaker, positions, movement, destinations, result and owner. Add model, band and mode to the technical map prepared by each team.

Download speech rehearsal worksheet (TXT)

Compare systems and follow the audio path

Model documentation and reference edition

Official ULX-D Dual/Quad manual v8.3 (2025-J), in English: channels, synchronization, Audio Summing, RF cascade and network modes. The link opens the manufacturer’s document; no local copy or reader was added.

Documentation consulted

Checked October 30, 2026: official sections for the specified procedures. Complete preparation through unit identification and tests of the actual feeds.

Let’s prepare your event system

Tell us what you want to show, hear or light and what your production already provides. Start with the idea and add models, dimensions and schedules later. Mention the model or guide in your message; the related service is selected in Contact.

Enquire about equipment and servicesView the related serviceEvent preparation guide