info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Sound

Shure ADTD: prepare IEM feeds, audio inputs and ShowLink

A monitor feed needs a complete path: console mix, transmitter input, audio channel, RF link and the listener’s receiver. This guide provides a planning matrix for ADTD while separating audio from control networking. Use it to agree responsibilities and records before load-in.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Model and documentation reference

ADTD is the two-radio Axient Digital PSM transmitter. The documentary scenario uses the AC variant and Narrowband to ADXR; it establishes no actual unit configuration. ADTQ is a different model; ADXR is the bodypack receiver. The ADTD product sheet identifies four analog/AES3 combo inputs, four Ethernet ports and two RF outputs. English ADPSM manual 2.2 (2026-E) supplies mode-specific conditions. Actual band, region, firmware and licenses remain unverified. The specified DC input applies to ADTDDC/ADTQDC, not every AC ADTD.

ADPSM User Guide · 2.2 (2026-E) · EN · ADTD product sheet · ©2024 · EN

Event application

For a show, conference or broadcast in Argentina, identify who needs each mix and who supplies console signals. Record listener roles, mix count, stereo or summed mono and the RF owner. Across venues, maintain a matrix for each unit and location. This scopes technical review without establishing inventory, local availability, an authorized band or a rehearsed system.

ADPSM User Guide · 2.2 (2026-E) · EN

Record four separate signal paths

Record four separate signal paths
PathADTD referenceProduction record
Console → rear inputXLR/TRS combo; rear Analog or AES3 selectionL/R source, assigned input, format and sensitivity or AES3 status/lock/rate
Network audioDante/AES67 documented; Dante Input Selection identifies L/RActual subscriptions, labels, clock and network mode pending
Channel → RF → ADXRNarrowband assigns a dedicated frequency to each stereo audio channelMix, preset, band and receiver; radios alone establish no enabled capacity
ShowLink remote controlCarries parameters, not audioAD610 access point and Network ID if remote control is required

ADPSM User Guide · 2.2 (2026-E) · EN

Trace each mix to its receiver

The proposed matrix is console L/R → selected ADTD input → audio channel → preset-dependent carrier → assigned ADXR. For Rear Panel, record the Analog/AES3 switch and the input displayed for the channel. For Dante, record L/R labels, patch and clock dependency; an Ethernet connection proves no received audio. Identify Stereo or Summed to mono. Operational presets apply at device level and availability depends on region. Narrowband and SC Narrowband are distinct options; do not transfer limits or features between them. The manual limits ADTD to two carriers/two antennas and notes additional channel licenses for some presets; this does not prove actual enabled channel count.

ADPSM User Guide · 2.2 (2026-E) · EN

Separate control, synchronization and network mode

ShowLink carries parameter data and is not required for the IEM audio link. Loss of that control alone establishes neither audio loss nor verified RF coverage. Rx ShowLink Network ID Update changes only the ID over IR: it does not sync audio parameters or assign a receiver slot. Sync (no link) sends RF/audio parameters without slot assignment; Sync additionally assigns a slot. Network operation also depends on mode: Switched carries control and primary Dante on all four ports; Split/Redundant uses 1/2 for control and 3/4 for primary/secondary Dante. Four sockets prove no operational redundancy. A separate PTP exception sends mono to AD4D/AD4Q/ADX5D in Standard, not HD, with overlapping bands; it offers no sync, link or encryption and transmits only L from stereo unless summed to mono. This is not treated as the same IEM scenario to ADXR.

ADPSM User Guide · 2.2 (2026-E) · EN

Prepare the system sheet before configuration

  1. Identify AC ADTD, label band, document revision and unit owner. Leave firmware, region, preset and licenses pending where records are missing.
  2. List mixes by listener role and console source. Mark L/R or summed mono, rear Analog/AES3 or Dante input and proposed channel without assuming patch or clock.
  3. Map channel, carrier/preset and proposed ADXR. Separate the RF plan, antennas and pending coverage; radios prove no enabled channels or permitted frequency.
  4. Record network mode, control/audio networks and ShowLink/AD610 needs. Distinguish Network ID Update, Sync (no link) and Sync without performing them.
  5. Assign audio, RF and listening-review owners and a rehearsal window. This preparation changes no networks, presets, power, frequencies, licenses or firmware and performs no sync/transmission.

ADPSM User Guide · 2.2 (2026-E) · EN

Frequently asked questions

Do four Ethernet ports establish redundant audio networks?

Mode and actual topology matter. Switched and Split/Redundant assign ports differently. Socket count is no verified redundancy.

Does ShowLink carry the mix to ADXR?

It carries no audio. It controls parameters through a ShowLink access point; identify audio, RF and control separately.

Does an IR Network ID update also sync audio?

No. Rx ShowLink Network ID Update changes only that ID. Sync (no link) and Sync differ in RF/audio settings and receiver-slot assignment.

Do two radios prove a fixed enabled mix count?

No. Preset, region and licenses affect capacity. The 2024 sheet includes planned-update features and proves no installed capability.

Does every Axient receiver use the same IEM link?

That is not assumed. ADXR is the IEM receiver in this scenario. PTP to AD4D/AD4Q/ADX5D is a separate Standard-mode mono link with its own conditions.

Complete the audio brief

Download the ADTD mixes, inputs, RF and control matrix

Identified official documents

Existing SHA-verified sources: English ADPSM User Guide 2.2 (2026-E) and English ADTD product sheet ©2024. Only PDF positions 1–4, 7–11, 21, 23–25, 42–51, 72–75 and 81–83 were read in the 95-page manual; visual inspection: 11, 24, 43, 50, 74 and 81. Product sheet: both pages read, page 2 visual. Translations 2.2 (2026-G) were neither read here nor assumed identical. Planned features in the 2024 note prove no installed capability. Official links; no new PDF copy, reader or equipment test.

Plan event sound

For event monitoring planning in Argentina, share city, venue, mix count, console/sources, audio format, identified unit/band, proposed receivers and audio/RF owners. State missing records. Equipment, compatibility, availability and rehearsal scope require confirmation.

Enquire about equipment and servicesView the related serviceEvent preparation guide