info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Sound

Allen & Heath SQ-5: remote calls, recording and scenes

Prepare house, remote-call and recording audio as separate feeds. Check USB source, tap point and filters before using a received file on SQ-5.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Equipment and operation for your event feeds

Tell us what the audience needs to hear and what stage, remote call and recording receive. Request sound equipment, setup, preparation and operation from Eventos Globales for conferences, presentations and shows in Argentina. Start with the running order and what the venue or production supplies; complete models, connections and schedules later.

Conference with a remote guest and recording

For a hybrid talk, define what the guest receives and what must be recorded. Call feed, house mix and recording tracks may require different content and controls. Preparing and checking those routes is part of the scope to quote.

SQ-5 and the required system

This page addresses SQ-5, not SQ5+. Separate processing channels from physical connections: it has 16 local preamps plus talkback and 12 XLR line outputs. The mixer combines local inputs and supported SLink, USB or optional-card sources. Identify installed hardware, firmware, expander and card; a control network socket does not establish Dante. Compare inputs, independent buses and computer connectivity for the conference.

Prepare a hybrid panel with separate feeds

  1. Label local voices, playback and far-end return. Plan LR for room sound, an aux to send local sources to the call minus its return, and a recording mix or isolated paths. Adapt this layout to the available buses and destinations.
  2. Check the pre/post point of each path and which mute controls affect it. A post-fader send follows channel level; a post-preamp recording Tie Line follows neither fader nor mute. If using Direct Out, check its global follow-fader and follow-mute settings. Decide between a program mix and unprocessed tracks.
  3. In Setup > Audio > USB, select USB-B for the computer or SQ-Drive for the intended path. SQ-Drive audio recording/playback cannot run at the same time as USB-B audio streaming. If the call uses USB-B, plan a compatible recording path rather than assuming SQ-Drive remains available. Test local voice, the remote participant and playback separately, monitoring the call and a played-back file. LR meters do not confirm those destinations.

Review a scene received from another operator

  1. Save the current show and check file version and origin. Protect outputs and agree on a time outside the program before loading the file or recalling a scene.
  2. Compare sockets, USB/SLink sources, preamp/phantom, buses, outputs, mutes and groups. Check global and scene filters: global filters take precedence and may prevent the expected recall.
  3. Rehearse scene recall and test one voice through each path. For missing audio, follow socket, channel, bus and output; restarting or replacing the full show is not the first test. Keep the previous file for recovery.

More setup questions

Does USB solve recording and conferencing automatically?

No. SQ-Drive audio recording/playback cannot run at the same time as USB-B audio streaming. Check USB source, patch, computer device and send/return paths; listen to the recorded file.

Does scene recall restore every setting?

Not necessarily. Filters, safes and show configuration affect recall. Check its scope before rehearsal.

Choose the USB path before combining calls and recording

SQ reference V1.6.0 Issue 2 and official USB help distinguish USB-B from SQ-Drive. SQ-Drive recording or playback cannot run simultaneously with USB-B audio streaming. If the call uses USB-B, prepare and test a compatible recording path in the system. Record computer device, USB source selection and send/return patch; listen back to the recorded file too.

Choose which controls each feed follows

A Tie Line can take post-preamp audio without following fader or mute. For Direct Out, check tap point and global follow settings. If house is muted while recording continues, compare the intended path before changing it: that may be the chosen behavior. Agree sources and controls per destination and test a small off-program change.

Preparation decisions

Why does recording continue when I mute speech in house?

Check whether the tap uses a Tie Line, Direct Out or a bus. Identify its tap point and mute/fader follow settings. Agree continuous tracks or an operated mix with production and rehearse both destinations.

Can I connect a Dante expander to the control port or SLink?

Identify the expander protocol and installed card. Network is for control and SLink supports documented systems; connector shape does not establish Dante. Prepare the map with the relevant connection guide before cabling.

Prepare the proposal and operator handover

Share city, date, running order and approximate source count. Identify venue-supplied items and tasks to delegate: equipment, setup, configuration, rehearsal or operation. Leave unknowns undecided. The worksheet is optional; downloading or completing it does not send an enquiry.

Download the USB, received-file and feeds TXT worksheet

Can I enquire before choosing a console or completing the file?

Yes. Tell us who speaks or plays content, who joins remotely and which destinations need audio. We can prepare alternatives and complete models, tasks and tests with your production.

Continue with the file and sound feeds

Official model references

Consult the SQ-5/SQ-6/SQ-7 getting-started guide, SQ reference V1.6.0 Issue 2 and USB help at the official site. This guide covers SQ-5, distinct from SQ5+. Compare document edition with the unit’s version.

Documentation consulted

Document review: October 30, 2026. Official model-specific references and editions; no equipment changes or inventory verification performed.

Let’s prepare your event system

Tell us what you want to show, hear or light and what your production already provides. Start with the idea and add models, dimensions and schedules later. Mention the model or guide in your message; the related service is selected in Contact.

Enquire about equipment and servicesView the related serviceEvent preparation guide