info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Video, LED and playback

Absen PL2.5 Pro 1/20: identify V10, V2 and control

Compare documented V10 and V2 revisions before selecting files or processing. Identify the actual cabinet receiver, dimensions and documentation.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Let’s prepare the display by identifying the panel

Tell us the intended use, approximate dimensions and which panels or equipment each participant supplies. We can evaluate LED system rental or purchase and preparation, installation, configuration, rehearsal and operation. If revision or control platform is unknown, start with available identification photos and the event goal.

What we define for a quote

Distinguish panel and processing supply, support and installation, power distribution, file preparation and operation. The proposal identifies revision, receiver platform, accessories and responsibilities. Specification data guide selection; unit and installation verification complete the scope before setup.

Which panel does this guide cover?

The Absen PL2.5 Pro is an indoor modular LED panel for video walls. This guide compares documented 1/20-scan versions of V10 and V2. A panel name or scan ratio alone does not identify its receiver, firmware or electrical configuration.

Treat the following as separate document revisions. They describe reference products, not a verified inventory unit. The 1/8 V10 version and PL2.5 XR V2 are outside this guide.

Differences that matter

V10 • 1/20 • V20221215
500 × 500 × 88 mm; 200 × 200 pixels; 3840 Hz; 16-bit grayscale. The specification includes 8.8 kg and 8.6 kg entries with the same heading; verify the applicable configuration before calculating load. Power supply servicing is specified from the rear.
V2 • NovaStar and Brompton • V20241206
Each control-specific table lists 500 × 500 × 78 mm; 7.8 kg; 200 × 200 pixels; 7680 Hz; 15-bit grayscale; maximum/average consumption 680/230 W/m², with ±15% tolerance. Power-box access is specified from front or rear.
Signal path
Video source → compatible LED processor → panel data chain. The processor must match the installed receiving system. Connector appearance does not establish protocol compatibility; verify the actual data and AC connector labels. Do not treat the panel data input as a direct HDMI or SDI video input.

What the system needs

Provide the exact panel revision, receiver model, compatible processor, manufacturer-approved cabinet configuration, pixel map, tested signal cables and suitable electrical distribution. NovaStar and Tessera projects are separate workflows; changing the processor does not by itself convert the installed receiver.

Use the matching mounting hardware and installation documentation. Include panels, frames, cables and accessories in the structural design. This comparison does not authorize a suspended or ground-supported layout.

Prepare the system

  1. Record label, revision, control platform, firmware and approved configuration. Keep a local backup before changing mapping or receiver parameters. Do not choose an RCFGX file from pixel pitch or scan alone.
  2. Confirm the processor input, source format and blackout state. Follow the actual panel data direction and patch plan; leave AC connection and distribution checks to qualified personnel.
  3. NovaStar: compare the detected receiver count and Screen Connection map with the physical chain. Brompton: use Add Fixtures From Network to inspect detected strings on the intended output before associating them on the canvas. Use the installed software's matching documentation.
  4. During rehearsal, display cabinet labels and a border at suitable brightness. Check image order and solid colors, then return to the intended content. Record results; these are proposed checks, not a physical test of this equipment.

Operating questions

Does 1/20 scan mean the V10 and V2 panels use the same settings?

Scan describes multiplexing. Verified specifications list 3840 Hz for V10 V20221215 1/20 and 7680 Hz for V2 V20241206 1/20. Identify revision, receiver and approved file; a shared scan ratio does not make a panel another revision or establish a software upgrade.

Match the panel revision, receiver and approved file before editing. For Brompton, verify a Tessera-compatible receiver and its fixture definition. Preserve the original NovaStar configuration; do not import it as a Tessera fixture.

A powered cabinet is black or shows the wrong section. What comes first?

Record whether the fault affects one cabinet or the rest of a chain. Inspect accessible data leads and compare the source, blackout state and expected cabinet count. In a planned test, substitute a known-good compatible data lead, changing one item at a time.

NovaStar: inspect detection and Screen Connection before sending parameters. Brompton: compare detection, association, placement and topology messages with the plan; steps depend on the change and version. Confirm the result with a pattern before accepting recabling. Preserve settings and plan intervention outside the program.

One repaired module has a different color. Should I erase its calibration?

First show the same solid-color pattern at the same brightness and note which area differs. Record panel/module revision, repair history and whether the difference remains at the same image position when changing the source content. Photograph the symptom and preserve the existing settings for service review.

Preserve coefficients and the project for a unit-specific manufacturer or authorized-service assessment. Check receiver configuration, calibration and replacement compatibility. Prepare changes with recovery and a comparison sample; the symptom alone does not identify a repair.

Symptom and next check

Absen PL2.5 Pro — 1/20
ObservationCheckNext step
Same name, different depthV10: 88 mm; V2: 78 mm in the cited revisionsMatch the label and specification before planning mechanics.
Black after recablingDetected chain and saved mapping/associationCorrect the verified route during rehearsal.
Uneven color after repairRevision, repair record and existing calibrationPreserve settings and request a model-specific service assessment.

Power, environment and installation

The cited 1/20 specifications list AC 100–240 V, IP40 front/IP21 rear and operation from −10 to +40 °C. Use the actual unit's electrical label and applicable manual. These indoor ratings do not establish rain protection; never infer panels per AC chain from an average-power figure.

For installation or maintenance, qualified personnel must review the unit’s applicable manual and accessories: grounding, protection, isolation, ventilation and disconnection procedure. Confirm each revision and installation separately; specification tables do not replace electrical or structural design.

Check frame and hanging/stacking compatibility, complete load and local conditions. Do not infer a safe panel count, outdoor use or load capacity from a brochure maximum. Stop operation for damaged electrical connections, moisture or overheating and have qualified personnel assess the system.

Record the system and rehearsal result

Use the existing LED worksheet and add full label, document revision, receiver platform and approved file provenance. Separate V10/V2 and NovaStar/Brompton tables. Preserve the current project and calibration coefficients for diagnosis; complete details with the panel supplier.

Download the existing LED worksheet (.txt)

Leave details undefined where needed. The worksheet downloads blank; retain your copy and describe the need in Contact. Preparing a worksheet or draft does not send an enquiry.

Continue with the identified component

Each guide retains its model and edition. Identify the actual unit’s platform before combining equipment, projects or files.

Documents by model, revision and platform

These are family PDFs: PL2.5 Pro V10 1/20 is on pages 4–5 of V20221215; PL2.5 Pro V2 1/20 is on pages 2–3 of V20241206, separately for Brompton and NovaStar. Use the reader’s page control. V10 1/8 and PL2.5 XR V2 are outside this comparison.

Documentation consulted

Review: October 30, 2026. Original V10/V2 PDFs checked by hash and relevant pages reviewed as text and images. Nominal revision-specific data; no Argentine unit, installation or calibration verified.

Let’s prepare your event system

Tell us what you want to show, hear or light and what your production already provides. Start with the idea and add models, dimensions and schedules later. Mention the model or guide in your message; the related service is selected in Contact.

Enquire about equipment and servicesView the related serviceEvent preparation guide