Model and documentation reference
Selected model: standard LEDBeam 150 RGBW, distinct from 150Q, FW, FWQ and LEDBeam 350. Shared manual 2.1 and DMX table 1.7 must match the actual variant. The manual documents 3.8°–60° zoom and two control modes; this candidate plans Mode 1 with 22 channels. Actual label, firmware, optics and accessories remain unidentified.
Robe LEDBeam 150/150Q · manual 2.1 · PDF 12/16 visual
Event application
For a small Argentine stage, mark ambient area, accent target, screen, people and cameras. Plan two states and a return, specifying what must stay stable during the effect. If someone speaks during movement, consider independent front lighting in the design. The mounting owner must review travel, audience and clearance before rehearsal; published pan/tilt range defines no approved path.
Robe LEDBeam 150/150Q · manual 2.1 · PDF 12/16 visual · Robe LEDBeam 150/Q/FW/FWQ · DMX 1.7 · exact variant required
Records that condition the result
| Function | Documented reference | Record to preserve |
|---|---|---|
| Position and width control | Mode 1 uses 22 channels; chart includes fine zoom | Exact personality and ambience/accent positions/width |
| Alternative mode | Mode 2 uses 16 channels | Changing mode changes footprint and function mapping |
| Color mixing | C Mix M selects RGBW/CMY; White inactive in CMY | Fixture mixing and console personality must correspond |
| Optional radio | Manual 2.1 describes external ROBE Wireless CRMX Dongle | Identify exact module/transmitter; do not assume included radio |
Robe LEDBeam 150/150Q · manual 2.1 · PDF 12/16 visual · Robe LEDBeam 150/Q/FW/FWQ · DMX 1.7 · exact variant required
Relate personality, address and signal path
The manual identifies five-pin DMX input/output. Record originating console/node, universe, address and LEDBeam 150 mode; a connector alone establishes no correct patch. For Mode 1, a planned start address 101 would occupy 101–122 only if version/personality match. The documented external CRMX module is a specific accessory rather than any XLR adapter or assumed installed receiver. Nothing was connected, linked or transmitted here.
Robe LEDBeam 150/150Q · manual 2.1 · PDF 12/16 visual · Robe LEDBeam 150/Q/FW/FWQ · DMX 1.7 · exact variant required
Separate a scene setting from a fault
BLC P/T can close output while pan/tilt values change; BLC DMC concerns position correction. Record both when comparing transition without disabling feedback/protection. C Mix M and virtual-color relationship can affect color; White is not active in CMY. Preserve personality, mixing and scene before attributing a difference to LEDs or calibration. Actual camera, LED frequency, curve and low-level behavior need a system rehearsal.
Robe LEDBeam 150/150Q · manual 2.1 · PDF 12/16 visual · Robe LEDBeam 150/Q/FW/FWQ · DMX 1.7 · exact variant required
Prepare three comparable states
- Identify standard LEDBeam 150 RGBW, known version and actual accessories. Preserve initial reference; infer no inventory/firmware from a shared manual.
- Draw ambience, accent and return-to-wash, including areas to keep stable. Mark audience/cameras/travel limits for qualified review; this package moves nothing.
- Prepare a signal row with universe, intended 22-channel Mode 1 and address. Check non-overlapping footprint; actual connection, patch and CRMX remain pending.
- Record RGBW/CMY, BLC P/T, BLC DMC, dimmer and width against transition intent. Plan light/shadow/camera/low-level observations without claiming tests.
- Agree on rehearsal owner/window and initial-state recovery. Perform no reset, calibration, feedback change, radio pairing or update to fill gaps.
Robe LEDBeam 150/150Q · manual 2.1 · PDF 12/16 visual · Robe LEDBeam 150/Q/FW/FWQ · DMX 1.7 · exact variant required
Frequently asked questions
Do Mode 1 and Mode 2 have equal footprints?
No. Manual 2.1 specifies 22 and 16 channels. Confirm mode/variant before preparing address/personality.
Why can output close during position changes?
BLC P/T documents blackout during pan/tilt changes, while BLC DMC concerns correction. Record scene/settings without diagnosing an actual fixture.
Should White behave the same in CMY?
No. Manual/chart mark White inactive in CMY. Verify mixing/profile correspondence before assuming a failure or recalibrating.
Does the LEDBeam 150 name establish built-in CRMX?
The consulted manual describes an optional external ROBE Wireless CRMX Dongle. Identify fixture/accessory/transmitter; presence or link was not tested here.
Does zoom make it a profile for a logo cut?
A beam-angle range establishes no shutters or gobo projection. Define wash/accent versus a cut and compare the appropriate documented function.
Follow the lighting control path
Official edition-specific documentation
Existing SHA-verified originals: 40-page LEDBeam 150/150Q manual 2.1, only PDF 1/2/11/12/16/20–22/40 read, 12/16 inspected visually. Seven-page DMX 1.7 table for 150/150Q/FW/FWQ read and PDF 4 inspected; apply only the selected RGBW unit scope. Official model-page text consulted. No full-manual read, new PDF copy or tested local reader.
