info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Sound

Radial ProD2: stereo playback, levels and connections

Connect keyboards or playback to the console while keeping left and right. Prepare adapters, mic inputs and levels so the audience receives the complete program.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Equipment and operation for your event feeds

Tell us what the audience needs to hear and what stage, remote call and recording receive. Request sound equipment, setup, preparation and operation from Eventos Globales for conferences, presentations and shows in Argentina. Start with the running order and what the venue or production supplies; complete models, connections and schedules later.

Prepare music and video playback for the room

For a presentation, conference or show, start with sources and console requirements. Request suitable interfaces or DIs, cabling, playback preparation and operation. An analog L/R output follows a different path from a computer offering USB only; tell us what you have and complete connections with our team.

Model and application

Channels
2
Design
Passive
Inputs / THRU
Quarter-inch
Outputs
XLR mic level
Input pad
−15 dB

ProD2 contains independent passive DI paths. It needs no phantom power and does not amplify a weak source. It is not an automatic stereo-to-mono merger.

Connections and required equipment

Source L/R → separate INPUTs → XLR outputs → microphone inputs. THRU carries the parallel source signal for a suitable local destination.

Prepare the system

  1. Lower levels and protect the system before connecting.
  2. Label left/right and check source adapter wiring.
  3. Test each path alone, then the intended stereo mix.

Questions and troubleshooting

Playback loses one side or sounds incomplete.

Check the source breakout before blaming the DI.

  1. Verify separate left/right feeds to the two INPUTs; check source and console panning. A stereo headphone plug is not automatically a balanced mono feed.
  2. Test one known source/cable per path at protected level. If the fault follows a cable or output, document it; do not tie source outputs together to force mono.
The signal is quiet or distorted.

Locate the level mismatch.

  1. XLR outputs are mic level; check the destination preamp and source playback level. THRU is a different output type.
  2. For distortion, check console clipping first; then compare the DI pad with controlled gain readjustment. Verify clean peaks. Persistent distortion needs source/cable comparison and service evidence.
Hum remains after using ground lift.

The DI switch only changes the audio ground path.

  1. Compare its built-in GROUND LIFT at protected level and record the result. List attached audio, video and control equipment.
  2. If hum persists, have the system technician inspect the signal paths and approved isolation options. Never remove protective earth, cut shields or modify mains wiring.

Choose the next check

Choose the next check
ObservationNext checkWhat to record
Missing sideBreakout/L-R patchSource and cable
Low/distortedMic input/pad/peaksSettings and meters
HumSignal ground pathsConnections and comparison

Precautions

  • Do not connect speaker-power outputs without an explicitly approved interface.
  • Keep protective earth intact.
  • A ground lift is a diagnostic option, not a promise to eliminate every noise.

Decide stereo, mono and the computer output

Define whether house, recording and monitors need stereo or a mono feed. Choose the summing point in an appropriate mix and test the complete content. Prepare a reference file and alternative playback; record which operator controls levels through videos, music and presentations.

Decisions for preparing the proposal

How do I prepare a mono room when the file is stereo?

ProD2 keeps its two channels separate and does not sum them. Prepare the mono mix in a suitable console or system and listen to the complete file, including speech and effects. The proposal can cover L/R patching, destination mixes and content checks; a cable tying outputs together does not replace that mix.

Does ProD2 take USB directly from my laptop?

Its inputs are analog. If the computer offers USB only, define a suitable audio interface or output and cabling to the DI or console. Tell us source model and available inputs; request prepared playback and connections without selecting every adapter yourself.

Prepare the proposal and operator handover

Share city, date, running order and approximate source count. Identify venue-supplied items and tasks to delegate: equipment, setup, configuration, rehearsal or operation. Leave unknowns undecided. The worksheet is optional; downloading or completing it does not send an enquiry.

Download the playback and analog-route TXT worksheet

Compare signal feeds and preamps

Official manuals and references

The manufacturer download page links the eight-page ProDI/ProD2 07-2025 manual, distinguishing mono ProDI and two-channel ProD2. References open on the official website.

Documentation consulted

Document review: October 30, 2026. Official model-specific references and editions; no equipment changes or inventory verification performed.

Let’s prepare your event system

Tell us what you want to show, hear or light and what your production already provides. Start with the idea and add models, dimensions and schedules later. Mention the model or guide in your message; the related service is selected in Contact.

Enquire about equipment and servicesView the related serviceEvent preparation guide