info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Lighting

LumiNode 4: plan sources, engines and DMX outputs

Plan lighting distribution for a conference, theater or show using a source → engine → destination map. Separate physical connectors, network universes and the decision about which controller should act.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Model and edition

The reference is LumiNode 4, product code LU 01 00071, and User Manual 20220629-REV 2.4.1. This number identifies the manual edition, not the installed firmware. LumiNode 4 DIN and Wall are different variants. Record model, firmware, active profile and programming responsibility before preparing changes.

Event application

For a stage front, stage rear and an ambient-lighting area, draw the destinations first. If a house console and a media server participate in the same lighting system, agree which attributes each controls and when. The map helps avoid selecting a general merge for a requirement that actually calls for backup or an operator handover.

Connections, processing and destinations are separate layers

Connections, processing and destinations are separate layers
Documented elementWhat it helps planWhat the actual setup must identify
4 five-pin XLR ports, configurable as inputs or outputsAssign physical DMX lines according to their role.IN/OUT direction, line, fixtures, fixture mode and start address.
2 network etherCON connectors and 6 process enginesAn engine processes data; it does not add a physical XLR. The manual defines up to four inputs and four outputs per engine.Protocol, source, universe, engine, destination and the relevant Group/VLAN.
Art-Net and sACN network inputsSelect protocol, universe and source; the manual explains Source IP conditions.Actual sender IP and transmitted universe number, separately from the console display label.

Manual PDF pp.29–30 and41; interface overview on p.12.

Choose what should happen to the sources

Forward routes one input to the selected destinations. HTP and LTP combine inputs using different policies; Backup gives the first of two inputs precedence. In this edition, Auto-recover is enabled by default and returns to the first input when it becomes available. With it disabled, recovery uses a configured control source. Record the policy and who authorizes the return; connecting two consoles does not demonstrate system continuity.

Manual PDF pp.34–35. The actual installation has not been tested.

Prepare the map and an off-program test

  1. Keep the configuration reference and the profile to recover. Record console/server, version, protocol, universe and IP for each source.
  2. Map each input to its engine and output. Confirm port IN/OUT direction and distinguish the universe from each fixture’s DMX address.
  3. Review the node network: this edition documents management and data on a shared interface or separated by Group/VLAN. Reaching the management web page does not prove reception of the lighting stream.
  4. Plan a test of each source separately, then the intended combination. Record transmitted values and destination response before altering the patch.
  5. If Backup is needed, agree loss, return and manual or automatic recovery. Also review DMX output time: continuous output retains the last received packets according to the manual. Record observations; do not infer blackout or recovery from the mode name.

Manual PDF pp.12,15,19–20,30 and34–35. These are documentary preparation steps, not an applied configuration.

Frequently asked questions

Do six engines mean six physical DMX lines?

No. This model has four DMX ports. Its six engines are processing resources; outputs may be physical or network destinations depending on the configured path.

Is merging two consoles the same as backup?

No. First decide whether they should act together or one should replace the other. Forward, HTP/LTP and Backup implement different policies; a system test confirms the result.

Does the output go dark when data is lost?

Do not assume that. The manual describes continuous DMX output enabled by default and output-time options. Compare current settings and fixture response during an agreed test.

What helps prepare a service quotation?

Tell us the event, venue, lighting areas and controllers your production provides. Add models, sources and recovery policy when available; signal distribution, configuration and operation can be evaluated for the agreed scope.

Connect the two parts of the signal path

GigaCore 10t: plan event ports, groups and network links

Worksheet for planning the map and test

Exact documentation

English original; the ES/PT guides are our own adaptations.

Documentation consulted

Document review: October 31, 2026. Cited pages read; no system test or installed-firmware identification.

Luminex · LumiNode 4: plan sources, engines and DMX outputs

Plan distribution for your event

Tell us which areas you want to light and how your technical team participates. We can evaluate equipment and services for distribution planning and operation. Mention LumiNode 4 in your message; the documented model is a technical reference and does not establish availability.

Enquire about equipment and servicesView the related serviceEvent preparation guide