info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Lighting

Color STRIKE M MV2: DMX profile, pixels and scene preparation

Separate RGB plate, white tubes and tilt using COLORSTRIKEMV2 manual Rev. 15 and chart Rev. 10; prepare the patch and camera rehearsal.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Lighting equipment and operation for your event in Argentina

Tell us what you want to light and what the venue supplies. Ask Eventos Globales about lighting rental, purchase and integration, and the setup, preparation and operation you need. Start with a photo or idea; the proposal identifies equipment, accessories and tasks for that project.

Prepare color, white and movement accents

Describe background color, white accents and moments requiring movement. Prepare a lighting enquiry with separate equipment, accessories, patching, programming and operation. State what general lighting, console and crew the venue provides; include the intended scene and cameras if recording.

Model and purpose

Manufacturer
Chauvet Professional
Model
Chauvet Professional Color STRIKE M
Documented product
COLORSTRIKEMV2; manual Rev. 15 / DMX chart Rev. 10
Light / movement
14 RGB sections; 28 white sections; 180° tilt
Control / connectors
DMX, RDM, Art-Net, sACN; IP-rated 5-pin XLR, etherCON and Powerkon
Power / environment
100–240 VAC, 50/60 Hz; −10 to 45 °C; 12.1 kg; IP65 with installation conditions

A tilting strobe/wash combining a color plate with white tube elements. It can create broad color looks, white bursts and segmented patterns, but the available controls and pixel grouping depend on the selected personality. Plan the look around the actual fixture and software rather than treating all strobe profiles as interchangeable.

Features and connections

Manual Rev. 15 and chart Rev. 10 for COLORSTRIKEMV2 V4.0.7 include 8, 11, 13, 24, 30, 47, 68, 74, 96 and 97 channel modes. Compare the supplied unit’s options before patching.

Network in/out, DMX in/out and power input have different functions. Select the intended Protocol and match IP/universe for Ethernet control or address/mode for wired DMX. Prepare compatible IP-rated cables/caps, the fixture profile and a documented electrical circuit allowance.

The mounting bracket requires a suitable rated clamp and verified support; overhead use requires a safety cable. Leave clearance for tilt and ventilation. Alignment pins do not establish the load capacity of an assembly.

Prepare the system

  1. Record SKU, fixture firmware and component versions from Information, then compare the console profile with that revision. Save the show and current fixture settings before changes.
  2. Match Protocol, DMX Channel and DMX Address/Start Address to the actual patch. Check the full footprint for overlaps and the universe boundary. A different personality changes the following addresses as well as the controls.
  3. Acclimate the fixture after a large temperature change. Connect grounded, protected mains, never a dimmer or rheostat. Test one isolated unit at low intensity with documented steady-light settings and a clear tilt area before using strobe effects.

Questions and troubleshooting

The color plate responds but white does not: which controls should I separate?

Check the personality and its master hierarchy before editing console libraries. For the documented 30-channel mode, the common intensity control can limit both sections.

  1. Confirm the exact mode on fixture and console. In that mode, compare channel 3 Master dimmer, channel 4 Plate dimmer and channel 5 Beam dimmer in the official chart.
  2. On an isolated unit, keep the shutter in its documented no-flash state and test each section at a safe low level while checking the common master. Inspect the console’s main and cell controls where its profile uses separate selections.
  3. Compare actual DMX values before recording independent cuelists. If the raw route works but the console controls differ, preserve the profile and investigate its mapping rather than opening the fixture.

Observe which section changes with each parameter and save received values. If the separation differs from the profile, we can review personality and firmware before rejecting the unit; do not sweep the control channel.

Why is a pixel pattern grouped, reversed or ignored after changing mode?

Channel count does not alone describe pixel layout. The 68-channel chart groups physical pixels; the 96 and 97 modes have different control assignments.

  1. Compare the selected mode’s pixel map and the order expected by the show. Check the actual DMX chart before reusing a profile from another fixture.
  2. Record Pixel Invert and LED Array Swap before changing them. The manual says array swaps can survive a factory reset, so a reset does not prove the default pixel order. Test one segment at a time.
  3. Record firmware and exact mode; compare the matching chart and save a repeatable condition. Plan any version change outside the active show using the applicable procedure.
An intensity fade feels delayed: how do I separate curve, cue and signal?

A reported delayed response is a symptom, not proof of a faulty fixture or a setting that affects every attribute.

  1. Compare one fixture’s Dimmer Mode with the intended response: OFF is linear; DIM1 is faster and DIM3 is slower. Record the original setting and compare an isolated steady-light fade.
  2. Compare the console’s fade and delay times with actual outgoing DMX changes. If DMX changes promptly but intensity fades differently, investigate the fixture’s dimmer response; do not extrapolate that result to tilt or every parameter.
  3. Record firmware and exact mode; compare the matching chart and save a repeatable condition. Plan any version change outside the active show using the applicable procedure.

Quick reference

Examples confirmed in the manual: start plus footprint minus one must not exceed 512.
Selected footprintHighest starting address
30 channels483
68 channels445
96 channels417
97 channels416

Precautions

  • Maintain at least 50 cm from adjacent surfaces for ventilation and keep flammable material outside 20 cm. Keep the tilt path clear, avoid direct viewing and coordinate strobe use and audience notices.
  • For outdoor IP65 use, power/data connections need suitable sealed cables and unused ports need secured covers. Do not submerge or treat the rating as approval for permanent extreme, saline or flood-prone installation.
  • Inspect housing, lenses and cables; stop if damaged or seriously malfunctioning. Disconnect before cleaning and refer internal repairs to qualified service. Adjustable PWM requires a camera test with the actual exposure settings; it does not guarantee universal flicker-free footage.

Terms on this page

DMX
A data protocol controlling lighting functions; each model defines what its channels mean.
RDM
Management communication for querying or configuring compatible equipment over a compatible path.
PWM
Modulation of LED output; interaction with a camera may produce recorded bands or variations.
Patch
Assignment of fixture, profile, address and universe in the control system.

Compare modes and record the intended look before rehearsal

In the 30CH mode of chart Rev. 10 for V4.0.7, channel 3 is Master dimmer, 4 Plate dimmer and 5 Beam dimmer. Other modes change the map and footprint. Save settings and select the profile from the supplied SKU and firmware; check plate, white and movement separately before recording the combined look.

Decisions for preparing the proposal

Can a camera scene be prepared without strobe?

Yes, start the enquiry with continuous color and movement at agreed moments. Share shots, frame rate, shutter and existing people lighting. Rehearsal with the actual camera helps assess exposure and bands; compare PWM settings within that test.

What should be defined when the venue has a desk and operator?

Identify who provides equipment and accessories, prepares profile and patch, programs the look and operates during the event. Assess a targeted addition or wider lighting scope. Start with the program and existing resources even if models are still to be defined.

Prepare the scope and operator handover

Enquire with city, date, scene idea and what production provides. State whether you need equipment, setup, preparation, operation or strike. Other details can remain to be defined. Lighting is selected in Contact; mention the model or guide in your message.

Continue with the console and the other lighting need

Model manuals, variants and charts

Links open official external English documentation: COLORSTRIKEMV2 manual Rev. 15 (10/2025) and DMX chart Rev. 10 for V4.0.7. Compare SKU, firmware and mode before reusing a show.

Documentation consulted

Checked October 30, 2026: current official product page, manual Rev. 15 and chart Rev. 10 consulted. Check functions and profile on the actual unit as well.

Let’s prepare your event system

Tell us what you want to show, hear or light and what your production already provides. Start with the idea and add models, dimensions and schedules later. Mention the model or guide in your message; the related service is selected in Contact.

Enquire about equipment and servicesView the related serviceEvent preparation guide