info@eventosglobales.com.arWhatsApp · +54 9 11 5626-6200

← Back to guides and resources

Reference documentation · Sound

QSC K12.2: event inputs, Thru and Mix Out

Choose the input for your source and prepare the feed to another destination. Separate gain, mixing and processing for K12.2 room or stage-feed use.

These guides help you prepare and check your production systems. Documented models are technical references; enquire about the equipment and services we can prepare for your project.

Equipment and operation for your event feeds

Tell us what the audience needs to hear and what stage, remote call and recording receive. Request sound equipment, setup, preparation and operation from Eventos Globales for conferences, presentations and shows in Argentina. Start with the running order and what the venue or production supplies; complete models, connections and schedules later.

Prepare speech, music and a stage feed

House and stage may need different content for a presentation, conference or show. Tell us sources, positions and feeds; request sound equipment, console, cabling, setup and operation from Eventos Globales. For purchase or frequent-use installations, compare the components and preparation you need.

Model and application

Model
K12.2, powered
Driver
12-inch, 2-way
Coverage
75° nominal
Input A
MIC / LINE
Input B
HI-Z / LINE

Read the rear label and firmware. K12 and other K.2 sizes need their own documentation.

Connections and required equipment

A and B accept audio. Thru carries its corresponding input before gain; Mix Out combines inputs after their gains. Neither output proves that the loudspeaker itself is reproducing sound.

Prepare the system

  1. Lower source and speaker levels before reconnecting.
  2. Match input sensitivity to the source; use LINE for a mixer line output.
  3. Record preset, EQ, delay and SUB MENU before changing them.

Questions and troubleshooting

Why does a mixer feed distort?

Check sensitivity before adding gain.

  1. Confirm LINE on the input receiving the mixer.
  2. Compare a known source and cable at controlled level; observe limiter activity.
  3. If LINE with an unclipped source removes distortion, the input sensitivity was relevant; verify clean audio at the required controlled level. If distortion remains with a known-good source and modest level, stop increasing gain and send the comparison to support.
Why does the next speaker ignore my gain change?

Check which output feeds it.

  1. Trace Thru versus Mix Out using the rear labels.
  2. Test one source and one destination; document the intended gain relationship.
  3. A pre-gain Thru should not follow that input-gain change; Mix Out should reflect its documented post-gain mix. Verify the chosen output matches the intended behavior, then restore rehearsal levels. Unexpected behavior on a confirmed path requires support, not a reset.
What should I record if protection recurs?

A forum report does not establish a firmware cure.

  1. Record the exact message, version, input conditions and ventilation.
  2. Remove the affected unit from service and refer recurring protection to qualified support.

Choose the next check

Choose the next check
ObservationNext checkWhat to record
DistortionInput mode and source levelInput, preset, limiter
Different downstream levelThru or Mix OutWiring and gains
ProtectionExact display and operating conditionsVersion and recurrence

Precautions

  • Use the mains rating and protective earth specified for the unit.
  • Do not open the amplifier or bypass protection.
  • Subwoofer filters, supports and suspension require the exact system documentation.

Prepare each source and destination

A supports MIC/LINE and B HI-Z/LINE; the 3.5 mm C input receives stereo and sums it to mono. Define whether playback must remain stereo across the system and how it will be mixed. For monitoring, prepare the required stage content at the console: a speaker monitor preset does not create a separate send.

Decisions for preparing the proposal

Does K12.2 EQ or delay also change Mix Out?

QSC identifies Mix Out as post-gain and pre-DSP. That cabinet’s EQ, delay and high-pass filter do not affect the output. Check destination processing separately; input gain and sensitivity changes do affect its analog signal path.

Does the K12.2 MIC input supply microphone phantom power?

The K.2 manual states that this input does not supply phantom. Identify microphone power requirements and prepare a compatible mixer or supply where needed. A wireless receiver also needs its planned power; selecting MIC does not replace it.

Prepare the proposal and operator handover

Share city, date, running order and approximate source count. Identify venue-supplied items and tasks to delegate: equipment, setup, configuration, rehearsal or operation. Leave unknowns undecided. The worksheet is optional; downloading or completing it does not send an enquiry.

The optional worksheet records speech positions and destinations. Add playback, selected outputs and settings to verify to the system plan. Downloading or completing it does not send an enquiry.

Download the existing voice rehearsal worksheet

Continue with the system and mix you need

Official model and signal-path references

The 23-page K.2 manual TD-000523-01-G and official notes on Thru, Mix Out and DSP. The manual covers several sizes; this guide concerns K12.2. References open on the official website.

Documentation consulted

Document review: October 30, 2026. Official model-specific references and editions; no equipment changes or inventory verification performed.

Let’s prepare your event system

Tell us what you want to show, hear or light and what your production already provides. Start with the idea and add models, dimensions and schedules later. Mention the model or guide in your message; the related service is selected in Contact.

Enquire about equipment and servicesView the related serviceEvent preparation guide